Відео

What size gauge your miging with

Little harder if you center the plate.. what you did was easy

you just got added to my Christmas list.

Nice welding bro,please can show your settings,

You need to fill in those craters at the end of your weld. They are where cracks will always start. If you also roll your wrist a bit it can help fill them in uniform and cleanly.

I watched a Norton disks video earlier; the chap said that with flat (cutting) disks it does not matter which way round. But the locking washer MUST be flush side down against the disk. The Norton guy also said that all recessed disks like grinding disks, should be mounted with the recess facing out (deepest part inwards), with the locking washer flat side outwards away from the disk, ie the center protrusion inwards.

splattertastic

Itd be easier to smooth your plate with a rock grinder, like yeah, you can use a cutting wheel but a rock, you just lay it down and its done

Wao 😮😮

Welding Galvanized is really not healthy without proper ventilation. It generates different gasses than regular stee. Do your research and be careful out there.

Nice, is it metal cored wire and what parameters did you use and the thickness of the material. ?

Why it is not at the middle? How it is better than welding in the middle of the plate?

I assume that corner is the weep hole ?

The company you work for can provide you with at least new protective gloves for the purpose of photography only

to achieve accuracy, formation is not done in that kind of way. the plate is marked in advance, we place the reinforcement, weld it and place it in the element. movement from the axis of the plate holes to the length given by the project. by marking the plate in place, the ears of the ipe hea or heb are never the same, for example if we take a heb 400 above is 400 below is 405mm. so the sleeve does not measure correctly, and the holes move

what do you recommend for i beam welding? stick or the one that u used? for structure

The only thing that I learn was that anyone can pickup a disk and turn it one way or the other in a video without educating us as to, should the label face up or down. I guess people will do anything to get a view on UA-cam. Maybe I should post a video asking “should I use my left hand or right hand to open a jam jar” and see how many hits I get.

Best tricks with out peper shabash

how to choose the type of welding ??? or TIG is the most widely used one ???

I don't think that is short circuit MIG, Spray Arc or globular. And yes! Clean surfaces for best results! MAG drills rock!

Any tips for 45° joint?

Bein ❤

Method 2 worked a treat for me. Easy to cut it out. Easy to weld it up and turned out nice and square. No more 45 degree mitre cuts for me!

❤❤

Like the 300,400= 500 trick ;-)

Them block outs looks rough with no radius

Now I’m legally blind..

Great job! Ur doing ur job properly, unlike my workplace who are also a structural steel fabrication company however they tack their plates on unclean and on rusty beams with mill scale too. This is the proper way to do it. Grind the weld area of any rust and mill scale for a stronger weld and reducing the risk of porosity or other weld defects which may lead to re-work. But once again, my workplace dont care and if they get porosity they just weld over it and theyre like "ohhh itll do"

So i take it the key is to cutting the plate on an angle so as to reduce the surface contact with the blade to the material...ergo saves the blade from being force through more metal less heat and blade warping amd risking teeth snap off....never thaught of it till the day i tried cutting a 3/8 plate with a 12" cutting wheel normally meant for cutting bolts and then i realised that standing the plate up in the vice you could get better results...so i suppose the principle is the same...may be a newb observation but eh...you gotta try and learn new ways eh

This is exactly how you are supposed to weld mig. No more stacking dimes because that’s actually a cold lap poor weld when you stack dimes. Nice work you could have welded for me ! I’d turn you loose and walk away and come back on payday to pat ya on the back!

Yes

May God’s peace and mercy be upon you, and thank you for the video that presents the content. I want to thank you for this content. For a simple request and I need help. I have been working as a welder for more than 20 years and I have evidence of experience and I have worked with major companies. I am from Morocco and I am looking for a work contract and immigration. Can you help me? Thank you. I needed welding, I am a good welder, you will not regret helping me

❤

.lm alktroda

.hawer weyo

Baliram fabricator

Been working on my pipe welding/ fit ups. This helps a ton for saddles. Thanks

Nice job, need to clean the steal before welding :)

Where do you buy the replacement railing pieces? They look very authentic

Wire diam?

#3❤

Why is this so cool . I know nothing about this and just can't stop watching

Drilling with gloves on 🥶

The best tricks aren't on youtube

How many ampers did u use? Around 65?

Studied up to 7th Class in School in 1996 Later did SSC through correspondence in 2018 Fabrication Works 12 years experience I want to good job sir I am Indian

What's the tolerance on that because that isn't flush at the flanges.

lo, like this is new. i learned this from an old timer 40 years ago, but i used an abrasive cut off saw. i also built many aircraft fuselages thin wall moly used a tin snip.

What kind of abrasive is that? That took that weld off really fast.